Difference between revisions of "Building the Mower"
| Line 127: | Line 127: | ||
File:SolderPaste-Example.jpg | File:SolderPaste-Example.jpg | ||
</gallery> | </gallery> | ||
Make sure to inspect your entire PCB and the alignment of all components before soldering with a hot-plate / oven / hot-air.<gallery> | Make sure to inspect your entire PCB and the alignment of all components before soldering with a hot-plate / oven / hot-air. See the photo below for an example of all xESC (STM32 version) components placed on the top side of the PCB, being inspected before soldering.<gallery> | ||
File:Solder Paste Inspection.jpg | File:Solder Paste Inspection.jpg | ||
</gallery> | </gallery>Here is a photo showing top and bottom of (3) completed xESC boards. (STM32 version) | ||
Here is a collection of photos of the OpenMower MainBoard from various Discord Users: (c.ez, vamatis, bhammy187) | |||
== Setup and test== | == Setup and test== | ||
Revision as of 16:23, 8 July 2022
Welcome to the OpenMower Building guide!
Note: This WIKI was only just started on 2022-04-22, but are actively working on filling it up and making a good documentation for the new builders out there!
Warning
Please note that this project currently is in a very early stage! So don't go buying stuff right away! You will need to order and solder your own boards, since there are no assembled boards for sale yet.
Please make sure that you're actually allowed to build this device in your area. There may be laws / patents prohibiting you of doing so!
Please just be responsible and if you're not sure what you're doing, please don't do anything.
BTW the warranty of your brand new mower will obviously be void as soon as you modify it in any way, so be aware.
Intro
Below you can find an overview of the major parts and components in the OpenMower.
There is a also another page with a Builder Road Map that gives guide to how to go about building your own OpenMower project.
Bill OF Materials
| Name | Description | Optional | Availability | Quantity Required | Source Link 1 | Alternate Source |
|---|---|---|---|---|---|---|
| Mower (Yardforce Classic 500) | Base building block | Off the shelf | 1 | https://amzn.to/3NWgIxk | Note: Earlier, we had a reference to myrobotcenter. However, they have gone into reconstruction, so be aware of that vendor! | |
| OpenMower Mainboard | The core of the new electronics. | Custom | 1 | Components Octopart BOM | WIP | |
| xESC | Motor drivers | Custom | 3 | Components Octoparts BOM:
- STM32 |
WIP | |
| Raspebrry Pi 4 | The brain of the robot. Also used to send RTK correction data from the base station.
|
Off the shelf | 2 | https://rpilocator.com/?cat=PI4&instock | WIP | |
| Ardusimple RTK2B GPS | Positioning system for the bot | Off the shelf | 2 | https://www.ardusimple.com/product/simplertk2b-basic-starter-kit-ip65/ | https://www.ardusimple.com/product/simplertk2b-basic-starter-kit-ip65/ | |
| Raspberry Pi Pico | Microcontroller talking to peripherals, soldered to the OpenMower mainboard | Off the shelf | 1 | Widely available | ||
| MPU 9250 | 9-axis accelerometer sitting on Mainboard allowing for direction through compass and dead reckoning of movement between GPS updates. | Off the shelf | 1 | You may need to shop around, corresponds to this one | https://aliexpress.com/item/1005003056348525.html
https://aliexpress.com/item/32787237588.html | |
| 3D printed brackets | To hold the GPS inside the bot | Custom | 1 | https://www.printables.com/fr/model/175826-openmower-gps-mount-for-yardforce-classic-500 | WIP | |
| SMA Angle Adapter | Needed to connect the GPS without bending the wire too much | Off the shelf | 1 | https://amzn.to/3K913b1 | WIP | |
| CC/CV Step Down module | As charger for the docking station | Off the shelf | 1 | https://amzn.to/3NUdRVL | WIP | |
| Docking Station Adapter PCB | A PCB to hold the module in place. | Custom | 1 | WIP | WIP | |
| GPS PCB | A ground plane PCB to improve GPS reception | Custom | 1 | WIP | WIP | |
| USB Angle Adapter | If you want to use the Classic 500's USB port | YES | Off the shelf | 1 | https://amzn.to/3ukNAIj | WIP |
Building the bot
Once you have gathered up all of the parts, components, tools, and have a set of PCB's, it's time to start building the OpenMower Robot.
First thing first, watch all of Clemen's Youtube video's, and then watch them again. They contain a Treasure Trove of information and should be used as a reference. https://youtu.be/_bImqD-pQSA
Get Organized: Before you start assembling and soldering the PCB's, it's recommended to organize all of your parts. One method is to print off the iBOM.html file, tape it to a piece of cardboard, and then put double sided tape next to each line item. Only take out the parts/components you need for (1) xESC at a time, or the parts for the Mainboard, then place them on the double sided tape. Here are a couple of examples:
Now you want to apply solder paste to your PCB, BUT, before you apply solder paste to your PCB's with a stencil, make sure to wipe down both the PCB and the stencil with isopropanol alcohol to clean the surface, this helps more than you would think. Once the IPA has evaporated, align your stencil on top of the PCB, and use masking tape or painters tape on one side to act as a hinge, so after you apply the solder paste, you can carefully remove the stencil. Please reference Clemen's Youtube video for soldering: https://youtu.be/Y16kbAK3vaU
Here is an example photo of a PCB after applying the solder paste:
Make sure to inspect your entire PCB and the alignment of all components before soldering with a hot-plate / oven / hot-air. See the photo below for an example of all xESC (STM32 version) components placed on the top side of the PCB, being inspected before soldering.
Here is a photo showing top and bottom of (3) completed xESC boards. (STM32 version)
Here is a collection of photos of the OpenMower MainBoard from various Discord Users: (c.ez, vamatis, bhammy187)