Difference between revisions of "Builder Road Map"

From Open Mower Wiki
Jump to navigation Jump to search
(→‎Further parts needed: updated BOM info and "getting parts" descriptions)
Line 63: Line 63:
|Use this to see where parts are available
|Use this to see where parts are available
|}
|}
 
=====Further parts needed=====
 
====Further parts needed====
You also need
You also need


Line 74: Line 72:
====xESC2040====
====xESC2040====


 
This version of the three motor drivers uses the RP2040 chip which should be available. The ESC can be produced single-sided for the OpenMower project (so it is less complicated than the STM32 version that is dual sided). xESC2040 has an option to mount some component on the underside to enable CAN interfacing, but, as said, this is not needed for the OpenMower.


{| class="wikitable"
{| class="wikitable"
Line 93: Line 91:
|https://github.com/ClemensElflein/xESC/blob/main/PCB/xESC2040/BOM/ibom.html
|https://github.com/ClemensElflein/xESC/blob/main/PCB/xESC2040/BOM/ibom.html
|Use this to see where parts are available
|Use this to see where parts are available
Note: this BOM is ''without''the CAN components for the underside (they are not needed for the OpenMower project).
|}
|}


====x-ESC (original STM32 version)====


This version of the three motor drivers uses the STM32 chip which is in very short supply, therefore the xESC2040 was designed and you should probably go for the xESC2040, unless you actually have access to STM32s. Also the STM32 version uses a double-sided PCB, so it is harder to solder than xESC2040.


====Getting the xESC's====
{| class="wikitable"
There are currently two versions of the xESC (of which you need 3 for the main board).
|+
 
!What
#An version based on the STM32 chip. Information about that is in the git repo https://github.com/ClemensElflein/xESC. That is working and tested, but it is hard to get the STM32s and the soldering is somewhat technical and one cannot order xESC pre-assembled (from e.g. JLCPCB) due to parts sitting on both sides of the PCB. But you can go ahead and build those now.
!Where
#A new version, simpler and cheaper, and based on the RP2040 chip. That is currently (2022-05-01) under final revision and should be available ca. medio May. That should be possible to order assembled from JLCPCB, once ready. So you might want to wait for that.
!Notes
 
|-
|Gerber files
|https://github.com/ClemensElflein/xESC/tree/main/PCB/xESC2_mini_VESC/GERBER
|Zip the files in this directory
|-
|BOM .csv file
|TODO
|
|-
|BOM on Octopart
|TODO
|
|}
===Base station with the base RTK GPS module===
===Base station with the base RTK GPS module===
[TODO] @c.ez : Need info.
[TODO] @c.ez : Need info.

Revision as of 10:45, 30 May 2022

Note: This WIKI was only just started on 2022-04-22, but are actively working on filling it up and making a good documentation for the new builders out there!

Warning

Please note that this project currently is in a very early stage! So don't go buying stuff right away! You will need to order and solder your own boards, since there are no assembled boards for sale yet.

Please make sure that you're actually allowed to build this device in your area. There may be laws / patents prohibiting you of doing so!

Please just be responsible and if you're not sure what you're doing, please don't do anything.

BTW the warranty of your brand new mower will obviously be void as soon as you modify it in any way, so be aware.

Intro

If you want to embark on building an OpenMower, we have collected an overview of the various parts and where find information and what to to below. Beware that this is not complete, but it gives you some navigation to how to go about making a project for yourself.

Please see the image to the right for an overview that will assist you when reading the road map description below.

You can find more information on the various parts in the page Building the Mower

Road map.png

Disclaimer

This material is provided as-is and free of charge. No guarantees of any kind are made that the information contained herein is exact or correct or does not violate any local regulations or cause any security risk. Any use you make of any information given here is at your own discretion and risk.

Road map

The Mower

Get a mower in a store

So far only the Yard Force 500 is supported. See FAQ for more about alternative mowers.

Disassemble the mower and Remove the old mainboard

See @c.ez's YouTube video https://www.youtube.com/watch?v=_bImqD-pQSA

Now, it is ready for a new main board.

PCBs with components

You need to build two PCBs; 1 for the main board and one for the three motor controls (ESCs). You have to get the PCBs, get the parts and solder it yourself at the current stage. Due to international parts shortage, getting parts is quite a detective task, but here, we give you some help.

The recommended process for getting parts is the following:

  1. There are some parts lists (BOMs) maintained in Octopart - they will be given below.
  2. Use the Octopart tool to find out where there are parts available and order them. You will very likely have to use several vendors. We propose that you start at digikey and then move on for parts that you can not get there.
  3. Order the parts.
  4. Use the relevant Gerber files for the board that you are making to order PCBs at e.g. JLCPCB. If you plan to use a hot plate or an oven for the soldering process, consider simultaneously ordering a stencil for placing solder paste on your PCBs.

Main board

What Where Notes
Gerber files https://github.com/ClemensElflein/OpenMower/tree/main/dist/Mainboard Get the latest zip file here.
BOM .csv file https://github.com/ClemensElflein/OpenMower/blob/main/dist/Mainboard/OpenMowerMainboard_bom_.csv With a little effort can be used to create an Octpoart list or a digikey list, if you spend some time mapping fields. The file has digikey and lcsc part numbers in it already.
BOM on Octopart https://github.com/ClemensElflein/OpenMower/tree/main/dist/Mainboard Use this to see where parts are available
Further parts needed

You also need

  • A Raspberry Pi 4
  • An RTK Module
  • A Raspberry Pi Pico

xESC2040

This version of the three motor drivers uses the RP2040 chip which should be available. The ESC can be produced single-sided for the OpenMower project (so it is less complicated than the STM32 version that is dual sided). xESC2040 has an option to mount some component on the underside to enable CAN interfacing, but, as said, this is not needed for the OpenMower.

What Where Notes
Gerber files https://github.com/ClemensElflein/xESC/blob/main/PCB/xESC2040/GERBER/ Use latest zip file here
BOM .csv file TODO
BOM on Octopart https://github.com/ClemensElflein/xESC/blob/main/PCB/xESC2040/BOM/ibom.html Use this to see where parts are available

Note: this BOM is withoutthe CAN components for the underside (they are not needed for the OpenMower project).

x-ESC (original STM32 version)

This version of the three motor drivers uses the STM32 chip which is in very short supply, therefore the xESC2040 was designed and you should probably go for the xESC2040, unless you actually have access to STM32s. Also the STM32 version uses a double-sided PCB, so it is harder to solder than xESC2040.

What Where Notes
Gerber files https://github.com/ClemensElflein/xESC/tree/main/PCB/xESC2_mini_VESC/GERBER Zip the files in this directory
BOM .csv file TODO
BOM on Octopart TODO

Base station with the base RTK GPS module

[TODO] @c.ez : Need info.

Charging Station

Get a CC/CV module

This is currently needed to fix the charging station provided by Yard Force due to incompatibilities with the replaced main-board. It should be possible to fix this issue, but right now, it is necessary. See Building the Mower for where to get it.

Upgrade the Charging Station

[TODO] @c.ez : Need info.